Intro:
Before you begin
Method 1: The Paper and Straw Kite
Step 1:
Make the frame
Step 2:
Attach the paper and tails
Step 3:
Make the string bridle
Method 2: The Classic Scott Sled Kite
Step 1:
Cut the kite fabric to size
Step 2:
Attach the frame
Step 3:
Attach the bridle

2torial #0479: Learn2 Make a Kite Up, up, and away! Kiteflying is a dedicated pursuit these days, an eco-friendly sport that's destined to pop up on the sports channels soon (or has it already?). Sponsored teams compete worldwide with dual-line, Kevlar-tethered, ripstop nylon techno-dreams that cost more than most people make in a week. Ratings are awarded champagne corks are popped, and competitors go home to arise at five a.m. and practice some more. But there's another world of kites out there. In this other world, kites are made from simple materials (often found materials), tethered with cheap cotton string, and flown by folks who arise from their desks at 5 p.m. looking for something fun to do. Fortunately it's still possible to make an inexpensive kite that's fun to fly and simple to build. Get on out there and have some fun! The kites shown here have three parts. First, there's the kite fabric. Made of paper or plastic tarp, it catches the wind. The frame, made of plastic straws or wooden dowels, gives the kite its shape. And then there's the bridle, which connects the kite to the main control line (the string that you hold onto the kite with). You'll find two different kites here. One is quite simple, while the other requires a little more care to build. But the main difference between the two kites is the quality of the materials. These can be found in your local hardware store or possibly around your house. Both can be assembled inexpensively and easily. Method 1: The Paper and Straw Kite A small, simple kite that costs almost nothing to build. Method 1 - Step 1 Method 2: The Classic Scott Sled Kite The Scott Sled is another simple kite, but more durable and convenient to transport. This kite flies well in very light breezes, so long as the line is kept taut. Refer back to the What you'll need section and collect the necessary materials. Find a spacious, clean, well-lighted workplace that you can safely make cuts on (not on wood floors or rugs). Method 2 - Step 1 Method 1: The Paper and Straw Kite Make the frame You'll create an H-shaped frame that you'll glue or tape some paper onto. First you'll make some notches on the two ends of one straw. This piece will be the center bar of the H-shaped frame. Carefully make one-inch cuts down the center of the ends of the straw. Now cut halfway across the straw at the bottomof each vertical cut.Half of the straw falls away and the other half remains. The result is a straw with notched ends.     Wrap the notched ends around the midpoints of the two vertical plastic straws. Secure this connection with tape.   Run the string through all four open ends of the straws. This will create a square. Tie an overhand knot and then a second one on top of the first one. Cut the string so that it's taut, yet doesn't bend the straws.

Method 1: The Paper and Straw Kite

Attach the paper and tails

• Cut one-inch squares out of the corners of a 10" by 12" piece of tissue paper. Place it under the frame that you've made.

   

• Fold the ends of the paper back over the straws and string. Secure the paper with tape or glue. The paper should be taut without bending the straws.

   

• Cut the garbage bag or the crepe paper to make two tails, each one 3' long. Tie them to two corners of the kite, where the two vertical straw ends stick out.

Method 1: The Paper and Straw Kite

Make the string bridle

• Cut two small holes in the paper, just below the point where the ends of the center straw connect the two vertical straws.

   

• Cut a piece of string about ten inches long. Thread it through the hole closest to the tails. Loop it around the center straw, and back through the same hole in the paper. Tie a double overhand knot to secure the string to the straw.

   

• Taking the end of the main control line, feed it through the other hole and tie it to the straw on that side.

   

• Finally, tightly tie the loose end of the first piece of string to the main control line, about three inches down from the paper.

You've just formed the bridle for your kite. The bridle can be adjusted by sliding the knot up and down where it's attached to the main control line. Experiment a little--with these adjustments you can make the kite fly better in different winds.

Method 2: The Classic Scott Sled Kite

Cut the kite fabric to size

The Scott Sled is another simple kite, but more durable and convenient to transport. This kite flies well in very light breezes, so long as the line is kept taut. Refer back to the What you'll need section and collect the necessary materials. Find a spacious, clean, well-lighted workplace that you can safely make cuts on (not on wood floors or rugs).

Follow the dimensions given here and detailed in the diagram below.

• Spread the tarp out on the floor. Use the marker and yardstick to indicate a 40" by 36" rectangle.

   

• On the rectangle's long sides, mark off four ten-inch sections. On the short sides, make a mark ten inches from the corners as shown in the diagram.

   

• Cut out the 40" by 36" rectangle with the razor blade and the yardstick.

   

• Using the 10" marks as guides, cut off the corners of the rectangle. These cuts create the outline of the kite fabric. Take a look at the diagram before you start slashing away.

   

• Use the blade and yardstick to cut out a triangular vent. Again, refer to the diagram for the correct location. This creates the final shape of the kite. What remains is to attach the kite fabric to the frame.

Attach the frame

This frame will make the kite fabric stiff in one direction, but flexible in the other.

• Take the three wooden dowels and lay them vertically on the plastic surface ten inches apart.

   

• Cut small, equal sections of the plastic packing tape to fix the ends of the dowels to the edges of the kite fabric. Wrapping the tape over the edge will create a strong sleeve where the end of the dowel can reside securely.

   

Attach the dowels to the rest of the kite fabric with more small sections of packing tape. Refer to the diagram to insure correct placement. Here's a spot that's easy to miss: go to the bottom of the triangular vent--that's the corner of the triangle with a 90 degree or right angle. Tape the dowel to the fabric here as well.

Attach the bridle

The bridle attaches to the outermost edges of the kite fabric (where the corner cuts were made). Before attaching the bridle itself, you'll reinforce the points where the bridle is attached to the kite fabric.

• Put squares of cloth tape on both of the outermost edges of the kite fabric. Consult the diagram for optimum placement. Trim the tape to match the contour of the plastic edge.

   

• Use the small grommet tool to place a grommet a half-inch in from edge of the fabric, where it forms the "point" on both side flaps.

   

• Take the six-foot piece of fishing line and fold it in half to find the center. Mark the centerpoint. Tie the swivel into the line at the centerpoint with an overhand knot.

   

• Thread each end of the fishing line through each of the grommets. Loop this end around to the front and tie it off, Include the side of the fabric in the tie-off. Your bridle is now formed, and your kite is finished!

   

To fly the kite, attach your kite line to the swivel in the middle of the bridle, and go find some wind!